HARDKERNEL ODROID-M1 4GByte RAM
A Home Assistant a 10.0 OS verziótól natívan támogatja az alaplapot! Az ODROID-M1 SBC (single board computer) hasznos perifériák széles választékát tartalmazza, melyeket különféle rendszeralkalmazásokhoz használhatunk. Az ODROID-M1 SoC (System on Chip) gyártója a Rockchip garantálja az ellátást a következő 15 évre, ezért úgy tervezhetünk, hogy az ODROID-M1 lapokat a B2B ügyfeleink számára 2036-ig vagy azt követően is tudjuk majd szállítani. Az M1 megközelítőleg ODROID-C4 teljesítményét hozza, de lényegesen több periféria csatlakozási lehetőséggel: pl. SATA. M.2 NVMe.
| A | Rockchip RK3568B2 CPU | N | 1 x Mono Speaker Output (1.3W at 8Ω load) |
| B | LPDDR4 RAM | O | 1 x SPI recovery Switch |
| C | 1 x Micro USB2.0 Device only | P | 1 x SPI Flash 16MiB |
| D | 1 x RJ45 Ethernet Port (10/100/1000) | Q | 1 x eMMC Module Socket |
| E | 1 x HDMI 2.0 | R | 1 x IR Receiver |
| F | 2 x USB 2.0 | S | 1 x RTC Backup Battery Holder |
| G | 2 x USB 3.0 | T | 1 x Reset jumper 1 x Power jumper |
| H | 1 x DC Power Jack | U | 1 x Micro SD Slot |
| I | 1 x M.2 NVMe M-Key PCIe3.0 2-Lane | V | 1 x SATA3 |
| J | 40 x GPIO Pins | W | 1 x SATA Power (5volt only) |
| K | 1 x MIPI CSI 2Lane | X | 1 x UART for System Console |
| L | 1 x MIPI DSI 4Lane | Y | 2 x System LED Indicators |
| M | 1 x 3.5mm Headphone Jack | Z | 1 x M.2 LED Indicator |
The CPU has four ARM Cortex-A55 processors with low power consumption and high efficiency operation at 2Ghz. The CPU and GPU performance is quite similar to our ODROID-C4.
A larger 8GB of LPDDR4 DRAM Memory is available while there is also a 4GB model for reduced cost.
Petitboot pre-installed into the on-board 16MiB of SPI-Flash Memory helps manage various OS and kernel versions easily and supports booting from microSD, eMMC, NVMe, SATA, and USB storage devices. In addition, since on-line OS installation using a network is possible, the cumbersome procedure of downloading and flashing an OS image is dramatically reduced.
A standard size 22mm x 80mm M.2 NVMe storage device can be directly installed on the ODROID-M1 board. The M.2 connector has PCIe 3.0 2-lane configuration which can deliver a blazing fast 1600MB/sec of sequential access performance. Note that M.2 SATA storage devices can not be used. The M.2 slot supports only a PCIe interface (M-Key).
|
Benchmark |
ODROID-M1 (PCIe 3.0 x 2) |
RPI CM4 (PCIe 2.0 x 1) |
|
fio 1M sequential read |
1646 MB/s |
416 MB/s |
|
iozone 1M random read |
1049.13 MB/s |
210.97 MB/s |
|
iozone 1M random write |
1163.95 MB/s |
188.70 MB/s |
|
iozone 4K random read |
43.73 MB/s |
14.77 MB/s |
|
iozone 4K random write |
96.90 MB/s |
25.38 MB/s |
A single native (non-USB) SATA 3.0 port is provided for use with a 2.5inch HDD or SSD NAND Memory storage device. This SATA interface delivers near 500MB/s of sequential access. The SATA Mount and Cable Kit contains a SATA Data cable, a SATA Power cable, and a mount plate with some support screws. However, since the SATA power port doesn’t have a 12Volt power rail, a separated external 12Volt SATA power supply is required to use a 3.5inch HDD.
A sleek and cool blue M1 Metal Case Kit is an available option to protect your ODROID-M1 board. The metal cover is made with aluminum extrusion that has an abrasive blasted surface texture and anodized blue finish. It can be securely docked to the ODRID-M1 heatsink frame via sliding slot. The front and rear side covers were made with gold plated PCBs.
Specifications
| FORM FACTOR | Board Dimensions: 90mm x 122mm x 16mm Heatsink Dimensions: 100mm x 123mm x 19mm Weight: 253 g including heatsink |
|---|---|
| PROCESSOR | Rockchip RK3568 Processor L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.992GHz) ARMv8-A architecture with Neon and Crypto extensions Mali-G52 MP2 GPU with 4 x Execution Engines (650Mhz) |
| NPU | 0.8Tops@INT8, integrated high-performance AI accelerator RKNN NPU Supports one-click switching of Caffe/TensorFlow/TFLite/ONNX/PyTorch/Keras/Darknet |
| MEMORY | 4 or 8GiB LPDDR4 with 32-bit bus width Data rate: 3120 MT/s, up to 1,560MHz |
| STORAGE | 1 x eMMC slot 1 x Micro SD slot (DS/HS mode up to UHS-I SDR104) 1 x NVME M.2 SSD (PCIe 3.0 x 2) 1 x SATA3.0 |
| NETWORKING | 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps) – Realtek RTL8211F (Ethernet transceiver) – LED indicators * Green LED: Flashing by data traffics at 100Mbps connection * Amber LED: Flashing by data traffics at 1000Mbps connection |
| VIDEO | 1 x HDMI 2.0 (up to 4K@60Hz with HDR, EDID) 1 x MIPI-DSI (works with 800 x 1280 LCD) |
| AUDIO | 1 x 3.5mm phone jack 1 x mono speaker output 1 x HDMI sound |
| EXTERNAL I/O | 2 x USB 2.0 host port 2 x USB 3.0 host port (or 1 x USB 3.0 host + 1 x USB 2.0 OTG port) 1 x Debug serial console (UART, 1.5Mbps N81) 1 x SATA Connector 1 x MIPI-CSI Camera Interface (15 pin) 1 x MIPI-DSI LCD Interface (31 pin) 1 x 40pin GPIO header |
| OTHER FEATURES | IR receiver for remote controller RTC and backup battery holder (to keep time and date for several months without main power input) System LED Indicators: – Red (POWER) – Solid light when DC power is connected – Blue (ALIVE) – Flashing “heartbeat” while Kernel is running. Solid On when in the u-boot stage. |
| POWER | 1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm DC input : 7.5V ~ 15.5V – DC 12V/2A power adapter is recommended – IDLE : ≃ 1.25W – CPU Stress : ≃ 4.44W (Performance governor) – Power Off : ≃ 0W |
We recommend powering the ODROID-M1 with a good quality 12V/2A power adapter.
(Br. 3.835 Ft)
(Br. 6.269 Ft)
(Br. 5.323 Ft)
