Bezár
Az oldal sütiket használ a felhasználói élmény fokozása céljából. Az oldal böngészésével elfogadja ezt. Értem Részletek
Kapcsolat: +36-53-571-114 | kisker@airlink.hu
Wireless-Bolt

Aeotec Dual Nano Switch w. energy metering Z-Wave

Ár: 17.866 Ft+Áfa (Br. 22.690 Ft)
db  
Termékadatok
Cikkszám:
ZW132-C
Gyártó:
Aeotec
Rövid leírás:

Az AEOTECH Nano Switch két különböző elektromos eszköz ki-/bekapcsolását képes elvégezni, használható pl. világítás, vagy ventillátor kapcsolására. A modul kis méretének köszönhetően könnyen szerelhető fali dobozba. Falkapcsolóval, bináris érzékelővel vagy a Z-Wave technológiával kapcsolható, szabályozható. Z-Wave gatewayen keresztül akár mobiltelefonról is vezérelhető.

Termékleírás

- Elektromos eszköz ki-/bekapcsolását képes elvégezni
- Kompakt méret
- A kimenet névleges árama: 15A
- Mobiltelefonról is vezérelhető
- Méretek: 40 x 44 x 20 mm
- 60mm-nél nagyobb fali dobozba szerelhető

Aeotec Nano Switch.

 

Aeotec Nano Switch has been crafted to power connected sockets and switches using Z-Wave Plus. It is powered by Aeotec’s Gen5 technology. 


To see whether Nano Switch is known to be compatible with your Z-Wave system or not, please reference our Z-Wave gateway comparison listing. The technical specifications of Nano Switch can be viewed at that link.

 

Familiarize yourself with your Nano Switch.

 

 

m2gzybPSurayOvBsgrfV4Hs__m7nE0Yc-A.png
35YugddsndGy0Fv6j-XtFruv_acSTHU7DA.png
 
Notes for the wire connection ports:

 

L – Power input for live

N – Power input for neutral

IN – Input for load power supply type (ie. if 120VAC is connected to IN, then OUT will output 120VAC to the load)

OUT – Output for load (This is directly connected to your Loads input to receive power).

S1 – External switch control for load

S2 – External switch control for load

 

 

 

Important safety information.

 

Please read this and other device guides carefully.The failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and / or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.

 

Keep product away from open flames and extreme heat. Avoid direct sun light or heat exposure.


110/120 volt editions of Nano Switch cannot exceed 15 amps. 220/230/240 volt editions should not exceed 10 amps. 

 

 

Install the Nano Switch.

 

 

Nano Switch installs behind a lighting switch or a momentary push button. It works with only 3-wire (with neutral) lighting setups, though each installation of Nano Switch is accordingly slightly different:

 

 

1. Shut off the main circuit breaker of your home for safety during the installation and ensure the wires are not short circuited during the installation which will cause damage to the Nano Switch.


 

 

 

Note: Your home’s main circuit breaker must support the overload protection for safety.

 

-ql-RI4qpNZm6KH3F4nNc35ZprH7mAp55Q.png

 

2. Preparing connection wires

 

14 AWG power wires for Input / Output.

18 AWG copper wires for external manual switch.

Use the wire stripper cut the metallic part of the  connection wire and make sure the length of the metallic part is about 5mm.

 

AXM8pGF3C5eHDse4aZJnmUrRMjwGNjJ3Kg.png

Note: All connection wires needs to be flexible cable.

 

Wiring diagram of 120/230VAC power input.

       

 
In some cases, you may have some loads just only can be used on the voltage of 24VDC and hope that it still can be controlled by the Nano Switch, so please refer to the following diagram to achieve this:
 
Wiring diagram of 120/230VAC power input connection to 24VDC power output. 
(Compatible to Nano Switch without Energy Reading [ZW139] only).

 

  

Note: The “IN” terminal should be connected to the  “-” of 24VDC input.

Warning: Nano Switch ZW116 is not compatible with this configuration, you must use Nano Switch ZW139 without energy reading.

 

Wiring diagram of 24VDC power input.

Since the Nano Switch also supports the 24VDC power input, so you can use it to control the loads that powered by 24VDC.

 

         

If the output loads should be only powered by AC120V or AC230V, you can change the wire connection as below:
 
Wiring diagram of 24VDC power input to 120/230VAC power output. 
(Compatible to Nano Switch without Energy Reading [ZW139] only).

 

                

Note: The “IN” terminal should be connected to the “Live” of AC 120V/230V power wire.

Warning: Nano Switch ZW116 is not compatible with this configuration, you must use Nano Switch ZW139 without energy reading.

 

All above wiring diagrams show that the Nano Switch uses 2-Way or momentary button switches as the external manual switch for 2-Way connection.

 

The below diagram will show you that the Nano Switch uses the SPDT (Single-Pole Double-Throw) switches as the external manual switch for 3-Way connection.

 

Wiring diagram of 3-Way connection for the external manual switch.

 

 

3. Install Nano Switch to the gang box.

a. Live/Hot wire connection: Connect the Live/Hot  wire to the “L” terminal on the Nano Switch.

b. Neutral wire connection: Connect the Neutral wire to the “N” terminal on the Nano Switch. 

c. Load wire connection: Connect the Load wire  to the “OUT” on the Nano Switch. 

d. External/manual Switch connection: Connect 2 18AWG wires to the “S1” and “S2” on the  Nano Switch. 

e. External/manual Switch connection: Connect 2 18AWG wires form the 2 terminals on the External/manual Switch to the Live wire.

 

 

pRU83KQ4KQrY9LHwCYYYZAi6BtmnJx3Ilg.png

Note: This is the physical connection diagram for 120/230VAC power input.


4. Mounting the gang box.

 

1. Position all wires to provide room for the device. Place the Nano Switch inside the gang box towards the back of the box. 

2. Position the antenna towards the back of the box, away from all other wiring. 

3. Reinstall the Nano Switch to the gang box.

4. Reinstall the cover onto the gang box.

 

5haP3YXJBUeacES6TtisC9FNTerEB4y96Q.png
Note:  1. The gang box should be sized 3×2×2.75 inch / 75×50×70 mm or larger, minimum volume 14 in / 230cm . 

          2. Use flexible copper conductors only.

 

5. Restore Power.

 

Restore power at the circuit breaker or fuse.

 

xfnwCD4ds-_WC3YW5_UOLpz11C46vqdxUg.png

 

 

 

Quick Start.

Adding your Nano Switch to a Z-Wave network.

 

After your Nano Switch is installed and powered on, you are now able to manually control the Nano Switch to turn it On/Off directly via pressing your Nano Switch’s Action Button, it is now time to add your Nano Switch to the Z-Wave network. To set your Z-Wave gateway/controller into pairing mode, please refer to the respective section within your controller instruction manual.

 

1. Set your Z-Wave controller into pairing mode.

2. Press the Action Button on the Nano Switch once or toggle the external manual switch once, the green LED (non-secure indication) will blink to indicate the Nano Switch is entering into pairing mode.

3. If the Nano Switch has been successfully added to your Z-Wave network, its RGB LED will be solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient. Repeat the instructions above 

from step 1.

 

With your Nano Switch now working as a part of your smart home, you’ll be able to configure it from your home control software/phone application. Please refer to your software or gateway user guide for further instructions on configuring Nano Switch to your needs.

 

The colour of RGB LED will change according to the output load power level:

 

Version LED indication Output (A)
US Green [0A, 7.5A)
Yellow [7.5A, 13.5A)
Red [13.5A, 15.5A)
AU Green [0A, 5A)
Yellow [5A, 9A)
Red [9A, 10.5A)
EU Green [0A, 5A)
Yellow [5A, 9A)
Red [9A, 10.5A)

 

Removing Nano Switch from a Z-Wave network.

 

Your Nano Switch can be removed from your Z-Wave  network at any time. You’ll need to use your Z-Wave network’s main controller. To set your Z-Wave controller/gateway into removal mode, please refer to the respective section within your controller instruction manual.

 

1. Set your Z-Wave controller into removal mode.

2. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession. 

3. if the Nano Switch has been successfully  removed from your Z-Wave network, its RGB LED will remain colourful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load), repeat the instructions above from step 1.

 

Kapcsolódó termékek
Aeotec Range Extender 6 Z-Wave Plus Gen5
KIFUTÓ TERMÉK. ELÉRHETŐ A KÉSZLET EREJÉIG. Az Aeotec Range Extender kiterjeszti Z-Wave okosotthon-központunk hatótávolságát, hogy akár pincéből,…
Ár: 10.401 Ft + Áfa
(Br. 13.209 Ft)
Részletek
Aeotec Range Extender 7 Z-Wave Plus S2
Az Aeotec Range Extender kiterjeszti Z-Wave okosotthon-központunk hatótávolságát, hogy akár pincéből, padlásról, garázsból is tudjuk a csatlakoztatott eszközeinket…
Ár: 14.015 Ft + Áfa
(Br. 17.799 Ft)
Részletek
Aeotec Range Extender 7 Z-Wave Plus S2 (2 PACK)
Az Aeotec Range Extender kiterjeszti Z-Wave okosotthon-központunk hatótávolságát, hogy akár pincéből, padlásról, garázsból is tudjuk a csatlakoztatott eszközeinket…
Ár: 22.519 Ft + Áfa
(Br. 28.599 Ft)
Részletek
Aeotec Smart Home Hub /WiFi,ZWave,ZigBee/
Aeotec Smart Home Hub vezérlőközpont az otthoni okosotthon eszközök automatizálására.
Ár: 37.639 Ft + Áfa
(Br. 47.802 Ft)
Részletek
Aeotec Z-Stick Gen5+ PLUS USB Z-Wave Plus adapter
Az Aeotec Z-Stick egy Z-Wave USB-adapter, aminek segítségével bármilyen számítógépet okosotthonközponttá lehet varázsolni. A beépített akkunak…
Ár: 18.109 Ft + Áfa
(Br. 22.998 Ft)
Részletek
Vera ezlo atom 2 Z-Wave 700 Controller WiFi
VERA applikációval kompatibilis WiFi-s Z-Wave vezérlő, mellyel számtalan eszköz irányítható akár mobiltelefonról. Az USB csatlakozó csak a tápellátás…
Ár: 16.457 Ft + Áfa
(Br. 20.900 Ft)
Részletek
VeraPlus Smart Home Gateway Z-Wave, ZigBee, BlueTooth, Wifi
A VeraPlus Gateway lehetővé teszi a egy Z-Wave valamint ZigBee hálózat irányítását webes felületen, okostelefonról vagy tabletről.Felhő szolgáltatás…
Ár: 63.268 Ft + Áfa
(Br. 80.350 Ft)
Részletek
Z-Wave.Me RaZberry 7 Pro (External antenna)
A Z-Wave.Me RaZberry 7 Z-Wave modul segítségével egy Raspberry Piből Z-Wave gateway készíthető.U.FL csatlakózós külső antenna nagyobb hatótáv eléréséhezZ-wave…
Ár: 31.488 Ft + Áfa
(Br. 39.990 Ft)
Részletek
Z-Wave.Me RaZberry 7 Z-Wave modul (PCb antenna)
A Z-Wave.Me RaZberry 7 Z-Wave modul segítségével egy Raspberry Piből Z-Wave gateway készíthető.Z-wave 700 széria - nagyobb hatótáv, jobb hatékonyság és…
Ár: 19.473 Ft + Áfa
(Br. 24.731 Ft)
Részletek
Z-Wave.Me RaZberry2 Z-Wave modul Raspberry Pi-hez
A Z-Wave.Me RaZberry2 Z-Wave modul segítségével egy Raspberry Piből Z-Wave gateway készíthető.Használható hozzá a Z-Way operációs rendszer, de a Home Assistant is…
Ár: 14.893 Ft + Áfa
(Br. 18.914 Ft)
Részletek
Z-Wave.Me ZMEEUZB1 Z-Wave USB adapter
A Z-Wave.Me UZB számítógéphez, notebookhoz vagy Raspberry Pi-hez csatlakoztatható, és integrált antennáján keresztül Z-Wave hálózatot hozhatunk vele…
Ár: 10.255 Ft + Áfa
(Br. 13.024 Ft)
Részletek